This creation started out as an original cast brass engine room light. After removing the battleship grey paint, it was polished. Next we added the brass deflector cover to dress it up just a little more. Four feet of polished chain was added so you can hang this eye catching light over your table or bar. This light has been re-wired with a new 110-120 volt UL Listed Fixture. A normal house bulb of 60 watts or less will work great. This light weight just about 9 pounds, so you really do not need much of a support hook to hang it. This light can be used inside or outside, it will last forever! This light measures 8 inches tall and 7 inches wide. It is shipped with 4 feet of the chain and wire.
** Click on image to the left to see additional images **
Item #P3-01
$175.00 plus shipping
Several matched pieces in stock!
CLICK ON PHOTO FOR MORE VIEWS
This is one of my custom hanging pendant lights. I started out with an original cast brass nautical light that was designed to mount direct to the ceiling. The original light measured 8 inches tall. The first thing we did was to sand blast off all the old paint and then polish the brass. Next I added the 7 inch brass deflector cover, it is attached to the globe cage and can be removed if you do not like this option. Next I installed the hanging chain using the four original mount holes on the base of the light. Four sections of chain come off the light and become one piece about 6 inches about the light. The final modification on this light was replacing the electrical system. I have re-wired this light for 110-120 volts and a new UL Listed bulb fixture was added. I normal screw in house bulb of 60 watts or less will work perfect in this light. The light comes with 48 inches of hanging chain and about 6 feet of electrical wire. Changing the bulb required no tools as the globe case and glass globe each screw right on to the base of this light. This light is ready to install right out of the box, and it is a one of a kind creation!
Item #P3-02
$175.00 Plus Shipping
Several matched pieces in stock!
CLICK ON PHOTO FOR MORE VIEWS
This light can be directly mounted to your ceiling, or it can be chain hung making it a very nice pendant light design.
This original cast brass ship's light has a 20 inch copper deflector cover. This is just the way we found it, other than a fresh polish job and new re-wiring. The main part of this light measures just about 12 inches tall and 10 inches wide. The top hatch cover is held in place by three wing nuts. The globe is 360 degree fresnel glass, and the globe is in outstanding condition! This light weighs 22 pounds.
This light has been re-wired with a new UL-Listed Westinghouse bulb fixture rated for any voltage less than 250 volts. A normal screw in house bulb of 100 watts of less will work fine in this light. I strongly recommend the use of a T-10 bulb in this light, as it will allow the globe to work more like a true lighthouse lens.
Like all of our brass lights, this light can be used in exterior or interior applications.
$525.00 Plus Shipping (as shown)
Item P3-03
We have 4 pieces in stock. 2 with copper deflectors and 2 with brass deflectors.
CLICK ON PHOTO FOR MORE VIEWS
These original cast brass nautical light was commonly used as a ceiling mounted lights in walk ways or work areas of the vessel. They would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling these lights will extend down from the ceiling by (A = 7 inches / B&C 8 inches). The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The ceiling mount holes on the "A" light are located about 3 1/2 inches on center of each other, and on the B & C lights the three mount holes are located about 1 1/2 inches off the center of the light. These lights can be used inside or outside application and it will last forever! If you use these lights outside, the glass must point towards the ground. Each light weighs 3 1/2 pounds.
These three do not match so pick the one you want, or take all three!
Item #P3-04 (A / B / C)
$100.00 Each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
**** I only have 1 piece of each light in this lot*****
Item #P3-05
SOLD
This light can be directly mounted to your ceiling, or it can be chain hung making it a very nice pendant light design.
This original cast brass ship's light has a 14 inch brass deflector cover. This is just the way we found it, other than a fresh polish job and new re-wiring. The main part of this light measures just about 9 inches tall and 6 inches wide. The top hatch cover is held in place by three wing nuts. The globe is 360 degree fresnel glass, and the globe is in outstanding condition! This light weighs 15 pounds.
This light has been re-wired with a new UL-Listed Westinghouse bulb fixture rated for any voltage less than 250 volts. A normal screw in house bulb of 100 watts of less will work fine in this light. I strongly recommend the use of a T-10 bulb in this light, as it will allow the globe to work more like a true lighthouse lens.
Like all of our brass lights, this light can be used in exterior or interior applications.
$425.00 Plus Shipping (as shown)
Item P3-06
Only One Piece In Stock!
CLICK ON PHOTO FOR MORE VIEWS
Item #P3-07
SOLD
The photo to the left looks like the cover is twisted or not on right, but this was caused by the angle of the camera.
Item #P3-08
$245.00 Plus Shipping
We have 3 pieces in stock
CLICK ON PHOTO FOR MORE VIEWS
Item #P3-09
SOLD
This is the same light as you see in the light listed just above (P3-09) except that the screw on cage of this one is extruded brass wire and the other light has a cast brass cage. These lights with the extruded brass wire cages tend to be about 1 inch shorter than the lights with the cast brass cage so the distance this light will extend down from the ceiling when mounted is more like 8 inches.
Item #P3-10
Priced $150.00 Plus Shipping
Several pieces in stock some may be slightly different but we can match several pieces if needed.
CLICK ON PHOTO FOR MORE VIEWS
Item P3-11
SOLD
This is an original brass engine room light. These nautical lights were also used in common work areas of the ship and many walkways. They are cast brass and weigh 8 pounds each. The globes are glass, and undamaged. Height of light is just over 9 inches. We have closed the original conduit holes in the sides of the junction box and drilled a new hole on the very bottom for the power wires to enter. Originally designed for outside use, this light has many inside decor uses! Re-wired with new 110-120 UL Listed fixture, and they are ready for installation!
Item #P3-12
$140.00 each plus shipping.
Several in stock some are slightly different.
CLICK ON PHOTO FOR MORE VIEWS
This is light can be mounted on top of a dock post or directly to the ceiling. We found these lights being used in the engine room and common walk ways of a German working class container vessel being scrapped at a salvage yard operation. The lights measure 8 1/2 inches tall. The base is 4 inches wide. The base is iron and the cage us polished brass. We sand blasted the bases because they were painted many different colors. The globe is glass, and undamaged. Re-wired with a new 110-120 UL Listed fixture. Any normal house bulb will work, but a T-10 Tube light will work best.
5 Pieces in stock.
Item #P3-13
$85.00 each plus shipping
CLICK ON PHOTO FOR MORE VIEWS
Item #P3-14
SOLD
Two lights of the same design, one is smaller than the other one:
The smaller light is now sold out
The larger light when mounted to the ceiling it will hang down 13 inches. The deflector cover is 10 inches wide on this light. The ceiling mount measures 3 1/8 X 4 3/4 inches and has four mount holes. The globe is glass and screws into the main light. Glass is undamaged. No need to worry about the wiring and bulb fixture, as we have installed all new Westinghouse parts that are UL Listed for up to 250 volts. The glass globe, globe cage, and the brass deflector cover spin off in one piece for easy bulb installation. This light uses a normal screw in house bulb of 100 watts or less.
Item #P3-15
Larger Light: $275.00 Plus Shipping
2 pieces of the large size in stock
CLICK ON PHOTO FOR MORE VIEWS
These lights look as good in person as they do in the attached photos. These lights were commonly found on US Liberty Ships. While you may think they were navigation lights, they were really used on the bridge and wheel house area at night for lighting. Made of all cast brass they measure just over 7 inches tall. The base mount measures 5 3/4 inches wide and has 6 mount holes. The globes are glass and undamaged. I have installed new wiring and a 110-120 Volt UL Listed bulb fixture that takes a normal screw in house bulb of 60 watts or less. Several pieces in stock.
Item #P3-16
$125.00 Plus shipping for one light
$235.00 Plus shipping for a pair
CLICK ON PHOTO FOR MORE VIEWS
Additionally, we have a few frosted globes to fit this light.
We call this the candle stick light. This solid brass electric nautical light measures 10 1/2 inches tall. The 360 degree glass globe measures about 7 inches tall and about 3 inches wide. This light was designed for outside use, but has many applications for inside lighting also. If you plan on using this light outside in a wet location, it is best if you hang it as shown in the photo to the left. For interior applications, this light can be hung any way you want. These lights have been re-wired for 110-120 volts, and have a new UL Listed Bulb Fixture.
I have 20 of these lights in stock.
Item #P3-17
Price $99.99 each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Item #P3-18
$125.00 plus shipping
Hurry, only 3 pieces left in stock!!!
CLICK ON PHOTO FOR MORE VIEWS
Item #P3-19
SOLD
This original cast brass nautical light was commonly used as a ceiling mounted light in walk ways or work areas of the vessel. It would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling this light will extend down from the ceiling by 7 inches. The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The ceiling mount holes are located 3 3/4 inches on center of each other. This light can be used inside or outside application and it will last forever! This light weighs 3 1/2 pounds.
5 matched pieces in stock.
Item #P3-20
$100.00 each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
This is a very cool original copper and brass nautical ceiling light. Just think, these were all painted green when we found them, and look what a few hours of polishing work can do! When mounted to the ceiling this light will hang down about 8 inches. The widest end of the copper cone cover measures 9 3/4 inches wide. The glass globe measures about 3 1/2 inches wide and about 5 inches tall. The copper cone cover, glass globe, and the brass cage unscrew as one piece to provide access to the bulb. We have re-wired this light with all new UL-Listed parts made by Westinghouse. The new wiring and parts are rated for any voltage under 250 volts. The new bulb holder takes a normal screw in house bulb of 75 watts of less. The ceiling mount has two bolt holes that are 3 1/2 inches on center of each other.
This is an uncommon light, and we have 13 pieces that are a close match.
Item #P3-21
$185.00 each, plus shipping
CLICK ON PHOTO FOR MORE VIEWS
These original cast brass nautical light was commonly used as a ceiling mounted lights in walk ways or work areas of the vessel. They would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling these lights will extend down from the ceiling by 7 inches. The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The ceiling mount holes are located about 3 1/2 inches on center of each other, except for "A" and this one has three mounts that are about 1 1/2 inches off center of the light. These lights can be used inside or outside application and it will last forever! If you use these lights outside, the glass must point towards the ground. Each light weighs 3 1/2 pounds.
Pick the one you want, or take all four. A & B have tops that are close, but different bases. C & D have tops that are close, but different bases.
Item #P3-22 (A / B / C / D)
$100.00 Each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
**** I only have 1 piece of each light in this lot*****
These original cast brass nautical light was commonly used as a ceiling mounted lights in walk ways or work areas of the vessel. They would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling these lights will extend down from the ceiling by 7 inches. The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The ceiling mount holes are located about 3 1/2 inches on center of each other. These lights can be used inside or outside application and it will last forever! If you use these lights outside, the glass must point towards the ground. Each light weighs 3 1/2 pounds.
Pick the one you want, or take all three. They are not a perfect match on the base, but the tops are the same.
Item #P3-23 (A / B / C)
$100.00 Each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
**** I only have 1 piece of each light in this lot*****
Item P3-24
$175.00 each, plus shipping (5 pieces in stock)
CLICK ON PHOTO FOR MORE VIEWS
Item P3-25
SOLD
This is an original heavy cast brass nautical light that can be used as a wall or ceiling light. It measures 9 inches wide and will extend out from the mounting surface by 5 1/2 inches. This light was designed to tilt 15 degrees out on one side. I think the tilt out design was intended to be used when the light was mounted to a wall it would tilt the housing down towards the floor just a little. We see this same light mounted on the ceiling, so my wall theory may or may not be right. We have re-wired this light with a new Westinghouse UL Listed bulb fixture rated for up to 250 volts. A normal house bulb of 50 watts or less will work just fine in this light. A short T-10 appliance bulb will also work in this light. This light has three mount legs on the back side. The glass globe is undamaged.
I have several of these lights in stock and I used the one with the worst polish job in the photos, so unless you get the one in the photo, yours will have a better polish job.
6 Pieces Left In Stock
Item #P3-26
$170.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Item P3-27
SOLD
Item P3-28
$190.00 each, plus shipping (90+ pieces in stock)
CLICK ON PHOTO FOR MORE VIEWS
Some of our stock in this design only have one conduit hole. The light shown has two conduit holes.
Item #P3-29
SOLD
This original cast brass nautical light has many different ways you can use it. You can mount this as a wall or ceiling light, or it can be mounted to a the side of your dock pilings or even near a base board to light up the walkway area.
This light measures 9 1/2 inches long and 5 inches wide. When mounted it will extend out from the mounted surface by 4 3/4 inches. It has four screw holes on the bottom side. Your mount screws are hidden inside the housing. The four wing nuts provide easy access to change the bulb. This light has been re-wired with new Westinghouse UL-Listed parts that are rated for up to 250 volts. Normal house voltage is not a problem. These lights require a T-10 bulb that you can get at most any hardware store for less than $5.00. It is recommended that the T-10 bulb for this light not exceed 20 watts due to the heat that can build up after extended use. The mount holes on the base of this light requires 2 1/2 inches of mounting surface to work.
This light is constructed of all cast brass and weighs 6 pounds.
Item: P3-30
$150.00 plus shipping (several matched pieces in stock)
CLICK ON PHOTO FOR MORE VIEWS
Item: P3-31
SOLD
You can use this original brass nautical light as a wall or ceiling fixture. It measures 8 1/2 inches wide (10 inches including the junction box). When mounted to the wall or ceiling, it will extend out by 4 1/2 inches. The top cover is held in place by three wing nuts that move freely. The globe is glass, and undamaged. The original power entered the light from the side of the junction box you see on the right hand side of the light. We have made a new screw in plug for the conduit hole. You can either use the original conduit hole, or hide the wires by drilling a new hole on the back side. This light weights 6 pounds.
This light has been re-wired with a new Westinghouse UL Listed bulb fixture rated for up to 250 volts. A normal 45 watt screw in bulb works perfect in this light. Our new wiring provides 24 inches of extra wire at the wall mount.
$150.00 Plus Shipping (ONE Piece Left)
Item: P3-32
CLICK ON PHOTO FOR MORE VIEWS
Item: P3-33
SOLD
If you are trying to get that nautical look in your decor and need a light that will work inside or out without the worry of falling apart, this is it!
Item P3-34
$225.00 Plus Shipping
Add a chain like P3-01 for $35.00 more
28 Pieces In Stock!
CLICK ON PHOTO FOR MORE VIEWS
These original cast brass nautical light was commonly used as a ceiling mounted lights in walk ways or work areas of the vessel. They would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling these lights will extend down from the ceiling by 7 inches. The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The ceiling mount holes are located about 3 1/2 inches on center of each other. These lights can be used inside or outside application and it will last forever! If you use these lights outside, the glass must point towards the ground. Each light weighs 3 1/2 pounds.
Pick the one you want, or take all three. They are not a perfect match on the base, but the tops are the same.
Item #P3-35 (A / B / C)
$100.00 Each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
**** I only have 1 piece of each light in this lot*****
These original cast brass nautical light was commonly used as a ceiling mounted lights in walk ways or work areas of the vessel. They would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling these lights will extend down from the ceiling by 8 inches. The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The three ceiling mount holes are located about 1 1/2 off the center of the light. These lights can be used inside or outside application and it will last forever! Each light weighs 3 pounds. If you use these lights outside, the glass must point towards the ground.
Pick the one you want, or take all four. They are not a perfect match on the base, but the tops are nearly the same.
Item #P3-36 (A / B / C / D)
$100.00 Each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
**** I only have 1 piece of each light in this lot*****
These original cast brass nautical light was commonly used as a ceiling mounted lights in walk ways or work areas of the vessel. They would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling these lights will extend down from the ceiling by 7 inches. The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The two ceiling mount holes are located about 3 1/2 off of each other. These lights can be used inside or outside application and it will last forever! Each light weighs 3 pounds. If you use these lights outside, the glass must point towards the ground.
Pick the one you want, or take all three. They are not a perfect match on the base, but the tops are nearly the same.
Item #P3-37 (A / B / C )
$100.00 Each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
**** I only have 1 piece of each light in this lot*****
This original cast brass nautical light has many different ways you can use it. You can mount this as a wall or ceiling light, or it can be mounted to a the side of your dock pilings or even near a base board to light up the walkway area.
This light measures 8 inches long and 3 3/4 inches wide. When mounted it will extend out from the mounted surface by 4 inches. It has two screw holes on the bottom side. The two screws that hold the cage in place can be removed to access the bulb area. This light has been re-wired with new Westinghouse UL-Listed parts that are rated for up to 250 volts. Normal house voltage is not a problem. These lights work best with a T-10 bulb that you can get at most any hardware store for less than $5.00, or a normal screw in bulb will also work. It is recommended that the T-10 bulb for this light not exceed 20 watts due to the heat that can build up after extended use.The mount holes on the base of this light requires a 3 1/2 inches of mounting surface to work.
This light is constructed of all cast brass and weighs 3 pounds.
Item: P3-38
$145.00 plus shipping (2 pieces in stock)
CLICK ON PHOTO FOR MORE VIEWS
This original cast brass nautical light has many different ways you can use it. You can mount this as a wall or ceiling light, or it can be mounted to a the side of your dock pilings or even near a base board to light up the walkway area.
This light measures 8 inches long and 4 inches wide. When mounted it will extend out from the mounted surface by 4 1/4 inches. It has two screw holes on the bottom side. The two screws that hold the cage in place can be removed to access the bulb area. This light has been re-wired with new Westinghouse UL-Listed parts that are rated for up to 250 volts. Normal house voltage is not a problem. These lights work best with a T-10 bulb that you can get at most any hardware store for less than $5.00, or a normal screw in bulb will also work. It is recommended that the T-10 bulb for this light not exceed 20 watts due to the heat that can build up after extended use. The mount holes on the base of this light requires a 3 inches of mounting surface to work.
This light is constructed of all cast brass and weighs 3 pounds.
Item: P3-39
$145.00 plus shipping (7 pieces in stock)
CLICK ON PHOTO FOR MORE VIEWS
We used two original brass nautical lights to make this ceiling fixture with double bulbs. The ceiling mount flange is 2 1/2 inches wide with three screw holes. When mounted to the ceiling, it will hang down 8 inches. You can reduce the distance it hangs down by cutting off the threaded rod it is suspended from. From left to right it measures 17 1/2 inches long. All new wiring and bulb fixtures have been installed. Your light will be shipped with two new 25 watt bulbs installed. The lights have screw on cages that hold the globes in place. The globes are glass, and undamaged.
Something just a little different that can't be found at Home Depot!
We have 5 matched pieces for your project.
Item #P3-40
$175.00 plus shipping
CLICK ON PHOTO FOR MORE VIEWS
This light is the same design as the ones used to make item P3-40. As shown in the photo, this light hangs down from the ceiling a total of 8 inches. The threaded down rod measures 2 1/2 inches long, so you can reduce the length of the light by shorting the threaded down rod. All new wiring and bulb fixtures have been installed. Your light will be shipped with a new 25 watt bulb installed. The light has screw on cage that hold the globe in place. The globe is glass, and undamaged.
Something just a little different that can't be found at Home Depot!
We have 4 matched pieces in stock for your project.
Item #P3-41
$95.00 plus shipping
CLICK ON PHOTO FOR MORE VIEWS
These original cast brass nautical light was commonly used as a ceiling mounted lights in walk ways or work areas of the vessel. They would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling these lights will extend down from the ceiling by 7 inches. The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The three ceiling mount holes are located about 1 1/2 off the center of the light. These lights can be used inside or outside application and it will last forever! Each light weighs 3 pounds. If you use these lights outside, the glass must point towards the ground.
No matches in this set, just some great looking lights! Pick the one you want, or take all four.
Item #P3-42 (A / B / C / D)
$100.00 Each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
**** I only have 1 piece of each light in this lot*****
This original cast brass nautical light was commonly used as a ceiling mounted light in walk ways or work areas of the vessel. It would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling this light will extend down from the ceiling by 7 1/2 inches. The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The ceiling mount holes are located 3 3/4 inches on center of each other. This light can be used inside or outside application and it will last forever! This light weighs 3 pounds.
5 matched pieces in stock.
Item #P3-43
$100.00 each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
Item #P3-44
SOLD
Here's a very nice little beehive spotlight. It measures just shy of 18" tall, with the bottom diameter being 12" from outside edge to opposite outside edge. We have made three modification to the light that makes it able to mount direct to the ceiling with all the wires hidden. The first modification is the original mount hole ring on the top bar has been cut flat to allow an even mount to your ceiling or other attachment point. The second modification called for the original goose neck conduit connection to be cut off and be replaced by a 1/2 copper tub that now hides all the wires when you mount it. The third modification was the installation of two 1/4 mount holes that were added to the top bar. These two new holes make it very easy to attach the light to your ceiling surface.
Item #P3-45
$350.00 Plus Shipping
We have several in stock!
CLICK ON PHOTO FOR MORE VIEWS Several Matched Pieces In Stock
Item #P3-46
$375.00 Plus Shipping
We have several in stock!
CLICK ON PHOTO FOR MORE VIEWS
Several Matched Pieces In Stock
These original cast brass nautical light was commonly used as a ceiling mounted lights in walk ways or work areas of the vessel. They would have been connected to a long line of conduit pipes that connected the power to several lights on one switch. We have made brass plugs for the original conduit holes and drilled a new hole on the ceiling mount surface to hide all the wires. The light has all new wires and bulb holder that are UL-Listed and made by Westinghouse. We also added the brass deflector cover to dress up the look of this vintage light. When mounted to the ceiling these lights will extend down from the ceiling by 7 inches. The brass deflector cover is 7 inches wide. The globe is glass and undamaged. To access the bulb area, the deflector cover, globe, and cage screw off as one piece. The base has four holes, but only two were really designed to be mount holes. The base measures 3 1/2 X 3 1/2 inches square. These lights can be used inside or outside application and it will last forever! Each light weighs 3 pounds. If you use these lights outside, the glass must point towards the ground.
Each light shown has the same base, but the glass globes are different in all four examples shown. Currently we have 5 pieces of the "A" light, 3 of the "B" light, 7 of the "C" light, and 3 of the "D" light.
Item #P3-47 (A / B / C / D)
$100.00 Each Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Add $35.00 and we will make it into a hanging light with chain like P3-01
These copper and brass nautical spot lights were mainly used on the bridge area to light up the work areas on the deck. While designed for outside use, they make great decor lights for the nautical interior. We added the small section of copper pipe to hide the supply wires. This light is ready to hang over your bar or table area. As shown, the heights of the light is just short of 15 inches tall. The mount plate on the cast brass arm is 3 3/4 inches wide and has four mount holes. The front surface of the spot light measures 9 1/2 inches wide and has a frosted glass cover for the bulb area.
I have re-wired this light with a 110-120 Volt UL Listed Bulb fixture, and it is ready for installation. Comes with 24 inches of extra wire.
A normal 60 watt or less house bulb works fine in this fixture.
Item #P3-48
$245.00 each, Plus Shipping.
CLICK ON PHOTO FOR MORE VIEWS
This is the last one of this design
$895.00 Plus Shipping
Item #P3-49
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
ONE PIECE LEFT IN THIS DESIGN!!
This is the first time we have seen this spot light design, and we may never see it again. Check out the mounting system on this light. It has three different angle adjustments. First, the wall or ceiling mount plate can rotate in different positions. Just below the ceiling or wall mount the two arms will swing 180 degrees. Right were the two support arms mount to the light, it again provides for the ability to swing another 180+ degrees. This light can be hung from the ceiling and pointed down as sown in the photo to the left, or you can use the three different angle adjustments to fit your needs. I also think this light could be mounted to a wall, and by using the adjustments you could point it in many different angles. Because I was not sure how you would use it, I placed an 8 foot power cord that can just plug into a normal three prong outlet. The plug and cord are exterior grade.
This light is all brass. As shown in the photo to the left, it stands 22 inches tall. The mount plate is 7 inches side to side and has three mount holes. The end with the glass measures 15 1/4 inches wide with the glass being 14 1/4 inches wide. To access the bulb, you can remove the ring the hold the glass in place, or the whole cone cover and glass is held on by three wing nuts. We have installed a new UL-Listed bulb holder that takes a normal screw in house bulb. The bulb holder and cord is rated for any voltage under 250 volts, but the three prong plug will only work in a normal 120 volt wall plug. Like most of these larger spot lights you can really step up the bulb wattage, but I think you will find a 100 watts or less with get the job done just fine.
Check out the other photos of this light by clicking your mouse on the photo to the left.
$595.00 each, plus shipping
Item #P3-50
$895.00 Plus Shipping
Item #P3-51
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
This is one of several very large copper and brass nautical spot lights that we have in stock. Commonly referred to as a "FOX LIGHT". These large lights were positioned several feet above the working deck area and were only used during loading and unloading operations. As shown, this light measures 25 inches from the top mount plate to the glass lens. The widest end measures 16 1/2 inches wide with the glass lens measuring 14 1/2 inches. This light weights just under 40 pounds. The mount plate measures 3 inches wide and has four screw holes. Mounting options can include attaching this right to the ceiling as shown. If you need your light to hang lower, you can add more sections of pre-threaded pipe to make it hang at the right position for your project. These pre-threaded pipe sections can be found at any hardware store in lengths of 1 inch up to 10 feet. We have installed a single 8 inch pipe in the attached photos. You can also suspend this light by chain. The chain would attach to the holes in the top mount plate and your wire would feed into the chain lengths. This light has been re-wired and a new 110-120 volt UL Listed bulb fixture has been installed that will hold a normal house bulb. You can use up to a 100 watt bulb with no problems.
$895.00 Plus Shipping
Item #P3-52
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
This light has nickel plating on the inside and outside of the copper housing.
$795.00 Plus Shipping
Item #P3-53
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00 Plus Shipping
Item #P3-54
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
This is a medium sized brass and copper nautical spot light. As shown in the photo to the left, it measures 16 inches tall. We have not modified this light other than giving it a total re-wire job. The new wiring is all UL-Listed rated for any voltage under 250 volts. The bulb fixture takes a normal screw in house bulb of 100 watts or less. The top arm or "U" bracket swings to the left or to the right, so you can mount it at almost any angle, or attach a chain and make it into a hanging light. The bottom end of this light is 12 inches wide and the glass is 9 1/2 inches.
$295.00 Plus Shipping
Item #P3-55
Only One Piece
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
NOT FOR SALE
Did you ever think what these large fox lights look like before we start to work on them? Click on the photo to the left and have a look at some photos showing what we start with.
$895.00 Plus Shipping
Item: P3-57
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00 Plus Shipping
Item: P3-58
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
Item: P3-59
SOLD
$895.00 Plus Shipping
Item #P3-60
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00 Plus Shipping
Item #P3-61
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00
Item: P3-62
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00 Plus Shipping
Item: P3-63
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
Item: P3-64
SOLD
$895.00 Plus Shipping
Item: P3-65
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00 Plus Shipping
Item #P3-66
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
Item: P3-67
SOLD
$895.00 Plus Shipping
Item #P3-68
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00 Plus Shipping
Item #P3-69
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00 Plus Shipping
Item: P3-70
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00 Plus Shipping
Item #P3-71
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
$895.00 Plus Shipping
Item #P3-72
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped
Item #P3-73
SOLD
$895.00 Plus Shipping
Item: P3-74
CLICK ON PHOTO FOR MORE VIEWS
The light shown in the photo is the light you will be shipped