|
Product
(click
image for more views) |
Description |
 |
This is an original 360
degree nautical light. This light was made by Nippon Sento, Co. Ltd.
Measures a little over 7 inches tall, and about 8 1/2 inches wide. Made
of all copper and brass. The glass globe is 360 degree fresnel and has
light wear. This light has the normal wear you would expect from a light
that has been used on a working vessel for many years. I have re-wired
this light with a new 110-120 UL Listed bulb fixture. The wires of the
power enter the bottom side on this light. Ready to install!
**
Click on image to the left to see additional images **
Item #P2-01
$135.00 Plus Shipping |
 |
This is an original 360
degree nautical light. This light was made by Nippon Sento, Co. Ltd.
Measures a little over 8 1/2 inches tall with the top bail down, and
about 8 1/2 inches wide. Made of all copper and brass. The glass globe
is 360 degree fresnel and has light wear. This light has the normal wear
you would expect from a light that has been used on a working vessel for
many years. I have re-wired this light with a new 110-120 UL Listed bulb
fixture. The wires of the power enter a new hole that I drilled on the
bottom. The original hole the wired entered has been sealed with a
removable sealer that will dry clear in color. Ready to install!
**
Click on image to the left to see additional images **
Item #P2-02
$145.00 Plus Shipping
|
 |
This is a solid brass post
light with a 360 degree fresnel glass globe. No makers' mark found.
Weight is about 8 pounds. This globe has little or no wear. As shown in
the photo to the left it stands 10 1/2 inches tall. The top plate is 7
inches wide when measured from bolt to bolt. The globe is about 5 inches
wide and about 4 1/4 inches tall. On the vessel, this type of light is
mounted to a threaded pipe that is welded to the deck. I have added the
iron base plate and the small section of 1 1/4 inch threaded pipe. You
can change the length of the threaded pipe to make this light shorter or
taller. I have re-wired this light and installed a new 110-120 UL Listed
bulb fixture that will hold a normal house bulb. The power wires enter
and the fixture from inside the base pipe to provide hidden access for
all wires.
The globe is much clearer in real life. The day of the photo, it was
in the cold warehouse, and then I shot the photos in the warm office.
End result was a globe that had a lot of condensation on it.
**
Click on image to the left to see additional images **
Item #P2-03
$150.00 Plus Shipping |
 |
This is a solid brass post light with a 360 degree fresnel glass globe.
You can see the remains of a makers' name on the lid, but the only word
that can be made out is "GENOVA". Weight is about 10 pounds. This globe
has little or no wear. As shown in the photo to the left it stands 10
3/4 inches tall. The top plate is about 6 1/2 inches wide. The globe is
about 6 inches wide and about 4 3/4 inches tall. On the vessel, this
type of light is mounted to a threaded pipe that is welded to the deck.
I have added the iron base plate and the small section of 1 1/4 inch
threaded pipe. You can change the length of the threaded pipe to make
this light shorter or taller. I have re-wired this light and installed a
new 110-120 UL Listed bulb fixture that will hold a normal house bulb.
The power wires enter and the fixture from inside the base pipe to
provide hidden access for all wires. The three wing nuts on the top are
what was on the light when we found it, but they look like they are not
original to this light.
**
Click on image to the left to see additional images **
Item #P2-04
$150.00 Plus Shipping
|
 |
This is a solid brass post
light with a 360 degree fresnel glass globe. No makers' mark found.
Weight is about 10 pounds. This globe has a few flake chips to the
raised edges. As shown in the photo to the left it stands 11 1/2 inches
tall. The top plate is 8 inches wide when measured from bolt to bolt.
The globe is about 5 3/4 inches wide and about 4 3/4 inches tall. On the
vessel, this type of light is mounted to a threaded pipe that is welded
to the deck. I have added the iron base plate and the small section of 1
1/4 inch threaded pipe. You can change the length of the threaded pipe
to make this light shorter or taller. I have re-wired this light and
installed a new 110-120 UL Listed bulb fixture that will hold a normal
house bulb. The power wires enter and the fixture from inside the base
pipe to provide hidden access for all wires.
**
Click on image to the left to see additional images **
Item #P2-05
$150.00 Plus Shipping |
 |
This is a solid brass post
light with a 360 degree fresnel glass globe. No makers' mark found.
Weight is about 10 pounds. This globe has a few flake chips to the
raised edges, but is in very good condition. As shown in the photo to the left it stands 10
3/4 inches
tall. The top plate is 7 inches wide when measured from bolt to bolt.
The globe is about 5 1/2 inches wide and about 4 3/4 inches tall. On the
vessel, this type of light is mounted to a threaded pipe that is welded
to the deck. I have added the iron base plate and the small section of 1
1/4 inch threaded pipe. You can change the length of the threaded pipe
to make this light shorter or taller. I have re-wired this light and
installed a new 110-120 UL Listed bulb fixture that will hold a normal
house bulb. The power wires enter and the fixture from inside the base
pipe to provide hidden access for all wires.
**
Click on image to the left to see additional images **
Item #P2-06
$160.00 Plus Shipping |
 |
This is a solid brass post
light with a 360 degree fresnel glass globe. No makers' mark found.
Weight is about 10 pounds. This globe has a few flake chips to the
raised edges, but is in good condition. As shown in the photo to the left it stands
just short of 12 inches
tall. The top plate is 7 inches wide when measured from bolt to bolt.
The globe is about 5 1/2 inches wide and about 5 1/2 inches tall. On the
vessel, this type of light is mounted to a threaded pipe that is welded
to the deck. I have added the iron base plate and the small section of 1
1/4 inch threaded pipe. You can change the length of the threaded pipe
to make this light shorter or taller. I have re-wired this light and
installed a new 110-120 UL Listed bulb fixture that will hold a normal
house bulb. The power wires enter and the fixture from inside the base
pipe to provide hidden access for all wires.
**
Click on image to the left to see additional images **
Item #P2-07
$160.00 Plus Shipping |
 |
This original nautical light is constructed of mostly
copper with some cast brass trim. No makers' mark, but I am sure this is
an English design. Measures 12 inches tall, and the base is 10 inches
wide. Has a 360 degree glass fresnel globe that is in very good
condition. I have re-wired this light and installed a new 110-120 UL
Listed bulb fixture that will hold a normal house bulb. I pulled the
electrical wires in from the base and placed a removable seal in the
original side hole.
**
Click on image to the left to see additional images **
Item #P2-08
$185.00.00 Plus Shipping |
 |
This is an original nautical light that was made by "Mariner SA in
Brasil". Constructed of all cast brass, this light weights 15 pounds. It
has a 360 degree fresnel plastic globe that has light wear. Measures 9
1/2 inches tall, and 8 1/2 inches wide. I have
re-wired this light and installed a new 110-120 UL Listed bulb fixture
that will hold a normal house bulb. I pulled the electrical wires in
from the base and placed a removable seal in the original side hole.
**
Click on image to the left to see additional images **
Item #P2-09
$190.00.00 Plus Shipping |
 |
This is the smallest set of solid brass bulkhead lights you will
find. The globes measure just over 4 inches tall and only 2 inches wide.
The way you see them in the photos to the
left, these lights measure just 8 inches tall, and will extend out from
the wall 2 3/4 inches. The hard part is already done, I have converted
them to 110 volts and re-wired them, and installed a new cork gasket. They will come to you with 25 watt
sewing machine bulbs already installed. The globes are glass. This light can
be used inside or outside, it will last a life time! Ready to install on
your project! Item #P2-10
$150.00 for two pieces. Plus Shipping |
 |
This is a 22 pound monster made of all cast brass.
Measures just short of 12 inches tall and 10 inches wide. The globe is
360 degree fresnel glass that has very light wear. Re-wired and has a
new 110-120 volt UL Listed bulb fixture that will take a normal house
bulb. T-10 appliance bulbs 40-60 watt work best in this light and you
can find them at any hardware store. Not sure what happened to the
makers' badge that once was attached to the lid. The base has three
mount holes that are about 3 1/2 inches outside of the center of the
base hole. The wing nuts do not look original and can be replaced with
no effort.
**
Click on image to the left to see additional images **
Item P2-11
$350.00 Plus Shipping |
 |
I hope you can tell more
about this brass prop by looking at the photos, because I am not real
sure what to tell you. Marked" 9 68 Grand Rapids. Mich. 16RH15" and
"16x15 1". This is about a 15 inch tip to tip prop and it weights about
10 pounds. I do not see any damage to this prop. The white stuff on the
leading edges is some sort of surface crud, not rock damage. I am
offering this as a wall hanger, if it works on your boat, then your are
the lucky one! **
Click on image to the left to see additional images **
Item #P2-12
$50.00 Plus Shipping |
 |
I hope you can tell more
about this brass prop by looking at the photos, because I am not real
sure what to tell you. This prop has lots of markings, please see all
the attached photos. Measures about 17 inches tip to tip and it weights
about 19 pounds. This prop has some rock damage. I am offering this as a
wall hanger, if it works on your boat, then your are the lucky one! **
Click on image to the left to see additional images **
Item #P2-13
$65.00 Plus Shipping |
 |
I hope you can tell more
about this brass prop by looking at the photos, because I am not real
sure what to tell you. This prop has lots of markings, please see all
the attached photos. Measures about 19 inches tip to tip and it weights
about 25 pounds. This prop has no rock damage. I am offering this as a
wall hanger, if it works on your boat, then your are the lucky one! **
Click on image to the left to see additional images **
Item #P2-14
$75.00 Plus Shipping |
 |
This is a Chris Craft Prop. I hope you can tell more
about this brass prop by looking at the photos, because I am not real
sure what to tell you. This prop has lots of markings, please see all
the attached photos. Measures about 18 inches tip to tip and it weights
about 24 pounds. This prop has no rock damage. I am offering this as a
wall hanger, if it works on your boat, then your are the lucky one! **
Click on image to the left to see additional images **
Item #P2-13
$75.00 Plus Shipping
|
 |
This is a pair of 1940's
Perko Air Vents from a motor yacht. The vents are cast brass with nickel
plating. I have mounted the vents to a piece of wood and added wall
hooks to the back of the wood. The Perko vents are a matched set and
have the perko makers' name on the inside of the cover. The wood
measures 8 1/2 X 11 1/2 inches. The vents are 9 inches tall, 5 inches
wide, and extend off the board surface by 3 1/2 inches. Perko
products were made in Miami, Florida. **
Click on image to the left to see additional images **
Item #P2-16
$165.00 Plus Shipping |
 |
I hope you can tell more
about this brass prop by looking at the photos, because I am not real
sure what to tell you. This prop has lots of markings, please see all
the attached photos. Measures about 19 inches tip to tip and it weights
about 25 pounds. This prop has no rock damage. I am offering this as a
wall hanger, if it works on your boat, then your are the lucky one! **
Click on image to the left to see additional images **
Item #P2-17
$75.00 Plus Shipping |
 |
I hope you can tell more
about this brass prop by looking at the photos, because I am not real
sure what to tell you. This prop has lots of markings, please see all
the attached photos. Measures about 18 inches tip to tip and it weights
about 20 pounds. This prop has some minor rock damage. I am offering this as a
wall hanger, if it works on your boat, then your are the lucky one! **
Click on image to the left to see additional images **
Item #P2-18
$65.00 Plus Shipping |
 |
I hope you can tell more
about this brass prop by looking at the photos, because I am not real
sure what to tell you. This prop has lots of markings, please see all
the attached photos. Measures about 18 inches tip to tip and it weights
about 20 pounds. This prop has some one chip on the leading edge of one
fin. I am offering this as a
wall hanger, if it works on your boat, then your are the lucky one! **
Click on image to the left to see additional images **
Item #P2-19
$65.00 Plus Shipping |
 |
This is a solid brass post
light with a 360 degree fresnel glass globe. No makers' mark found.
Weight is about 10 pounds. This globe has a few flake chips to the
raised edges, one or two are bigger than I like to see. As shown in the photo to the left it stands
just short of 11 1/2 inches
tall. The top plate is 4 5/8 inches wide not counting the bolts.
The globe is about 5 inches wide and about 4 1/2 inches tall. On the
vessel, this type of light is mounted to a threaded pipe that is welded
to the deck. I have added the iron base plate and the small section of 1
inch threaded pipe. You can change the length of the threaded pipe
to make this light shorter or taller. I have re-wired this light and
installed a new 110-120 UL Listed bulb fixture that will hold a normal
house bulb. The power wires enter and the fixture from inside the base
pipe to provide hidden access for all wires.
**
Click on image to the left to see additional images **
Item #P2-20
$120.00 Plus Shipping |
 |
I placed the 12 OZ Coca-Cola can next to this light so you have ideal
how big it really is. This light weights about 24 pounds. It measures
over 12 inches tall. The reflector pan base measures 20 inches wide and
the cast brass light is 10 inches wide. The globe is 360 degree fresnel
glass. The globe is like new! I have rewired this light with a new
110-120 volt UL Listed bulb fixture. The bulb fixture holds a normal
house bulb. Because the inside of this light is so big, you can put up
to a 100 watt bulb with no problems. I have started using the T-10
Tubular appliance bulbs in lights like this because they make use the of
tall fresnel globe.
This light can be mounted to the ceiling of a large room, out on the
porch, or under the dockhouse roof. It will catch the attention of
everyone!
Ready to install, and in great condition!
Item #P2-21
$650.00 Plus Shipping |
 |
This is a nice clean original nautical bulkhead light made by
"Appleton". The grey colored base on this light is iron. The part of the
base that the brass cage threads to is aluminum. Most people call this a
Liberty Ship Light because of the construction. I did not remove this
from a Liberty Ship, this is just a style name given to lights of this
construction. Measures 10 1/2 inches tall, and will extend out from the
wall by 5 inches when mounted. The mount plate is 4 1/2 inches wide and
has 4 mount holes. I have re-wired this with a new 110-120 volt UL
Listed fixture, so it is ready to install.
**
Click on image to the left to see additional images **
Item #P2-22
$110.00 Plus Shipping |
 |
This is an original nautical bulkhead light made by "Appleton". The
copper colored base is copper plated iron. The part of the base that the
cage threads to is aluminum. Most people call this a Liberty Ship Light
because of the construction. I did not remove this from a Liberty Ship,
this is just a style name given to lights of this construction. Measures
10 1/2 inches tall, and will extend out from the wall by 5 inches when
mounted. The mount plate is 4 1/2 inches wide and has 4 mount holes. I
have re-wired this with a new 110-120 volt UL Listed fixture, so it is
ready to install. The cage has a makers' name "Kondu", and the base has
a makers' name of "Appleton". This light would use some cleaning. The
top housing has a casting crack near the front hole, but it will last
forever.
**
Click on image to the left to see additional images **
Item #P2-23
$85.00 Plus Shipping
|
 |
This is a solid brass post
light with a 360 degree fresnel glass globe. No makers' mark on main
light, but base is marked "KONDU".
Weight is about 9 pounds. This globe has no damage. As shown in the photo to the left it stands
9 1/2 inches
tall. The top plate is 5 5/8 inches wide not counting the bolts.
The globe is about 5 1/2 inches wide and about 4 3/4 inches tall. I have re-wired this light and
installed a new 110-120 UL Listed bulb fixture that will hold a normal
house bulb. The power wires enter and the fixture from inside the base
pipe to provide hidden access for all wires.
**
Click on image to the left to see additional images **
Item #P2-24
$145.00 Plus Shipping |